> >>Shields

Information

New products

Shields There are 16 products.

Showing 1 - 16 of 16 items
  • 2,40 € Available

    Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already

    2,40 €
    Add to cart More
    Available
  • 2,60 € Available

    Prototype Size:7cm x 5.5cm x 2cm Mini breadboard size: 4.4 x3.4 x1cm Self-adhesive breadboard SOIC place for IC Buttons: 2 LED: 2 Package Included: 1 x Arduino Prototyping Prototype Shield Proto Shield Board 1 x Mini Breadboard 170 Points.

    2,60 €
    Add to cart More
    Available
  • 3,40 € Out of stock

    Drives 4 DC or 2 stepper or 2 Servo motors Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single/double coil or interleaved stepping 4 H-Bridges: 0.6A per bridge (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC 2 external terminal power interface, for...

    3,40 €
    Add to cart More
    Out of stock
  • 12,40 € Available

    Ethernet Module ENC28J60 SPI interface mini version

    12,40 €
    Add to cart More
    Available
  • 15,90 € Out of stock

    The Wireless Proto shield allows an Arduino board to communicate wirelessly using a wireless Xbee module from Digi. It can also use any module with the same footprint. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight).

    15,90 €
    Add to cart More
    Out of stock
  • 19,50 € Available

    Ethernet Shield, based on the Wiznet W5100 Chip Supported by the official Ethernet Library Micro-SD card slot Compatible with Duemilanove (168 or 328), Uno & Mega (1280/2560) Network (IP) stack capable of both TCP and UDP Supports up to 4 simultaneous socket connections

    19,50 €
    Add to cart More
    Available
  • 22,00 € Out of stock

    Innoesys Educational Shield is an Arduino UNO shield that has all the necessary components and sensors on it, for the beginner to start programming Temperature Sensoor Potentiometer Photo Sensor Relay Servo Motor Support ON-OFF Switch Buzzer 3 x LEDs (Red, Green, Blue) 5 x Pushbuttons Manufacturer: Innoesys (www.innoesys.com) For detailed information and...

    22,00 €
    Add to cart More
    Out of stock
  • 24,80 € Out of stock

    The Arduino 4 Relays Shield is a solution for driving high power loads that cannot be controlled by Arduino's digital IOs, due to the current and voltage limits of the controller. Operating Voltage: 5V Coil current consumption: 140 mA (with all releays on, about 35mA each) Single pole chargeover contact maximum current: 30V DC 2A Maximum load voltage:...

    24,80 €
    Add to cart More
    Out of stock
  • 25,10 € Out of stock

    The Arduino Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. Operating Voltage: 5V to 12V Motor controller: L298P, Drives 2 DC motors or 1 stepper motor Max current: 2A per channel or 4A max (with external power supply) Current sensing: 1.65V/A

    25,10 €
    Add to cart More
    Out of stock
  • 28,00 € 30,00 € Available
    Sale!

    Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory) LoRa™ Modem FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation Bee form factory Package Includes: 1 x Lora Bee 1 x Glue Stick Antenna(868 MHZ, 433 MHZ or 915 MHZ depends on order) Environmental protection paper box

    28,00 € 30,00 €
    Add to cart More
    Available
  • 32,00 € Out of stock

    Microchip MCP4728 12-bit Quad channel DAC 4 analogue buffered or un-buffered outputs Voltage gain using potentiometer Jumper Configurable Voltage amplifier with external power source up to 26V Manufacturer: Innoesys (www.innoesys.com) ** For detailed information refer to the datasheet below

    32,00 €
    Add to cart More
    Out of stock
  • 32,30 € Available

    The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. A000024 (without PoE) 

    32,30 €
    Add to cart More
    Available
  • 36,30 € Out of stock

    Compatible with 3.3v or 5v I/O Arduino Board. Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in factory) Low power consumption Compatible with Arduino Leonardo, Uno, Mega, DUE External Antenna via I-Pex connector

    36,30 €
    Add to cart More
    Out of stock
  • 39,00 € Out of stock

    The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. A000025 (with PoE) 

    39,00 €
    Add to cart More
    Out of stock
  • 39,80 € Out of stock

    Innoesys LoRa Shield is an Arduino shield for Low-Power Wide-Area Networks (LPWAN) designed for long range communications with low bitrate. *** Long range: greater than 15 km *** Applications: Internet of Things Sensor networks Agriculture applications Industrial automation Smart city Smart meters Home automation Manufacturer: Innoesys (www.innoesys.com)...

    39,80 €
    Add to cart More
    Out of stock
  • 49,00 € Out of stock

    The LoRa/GPS Shield is an expension board for LoRa™/GPS for using with the Arduino.This product is intended for those interested in developing LoRa™/GPS solutions.The LoRa/GPS Shield is composed of LoRa/GPS Shield mother board and LoRa BEE.

    49,00 €
    Add to cart More
    Out of stock
Showing 1 - 16 of 16 items