Information

New products

Peripherals There are 122 products.

per page
Showing 1 - 18 of 122 items
  • 0,20 € Available

    Photoresistor is a resistor which made of semi-conductor material,and the conductance changes with luminance variation . The photoresistor can be manufactured with different figures and illuminated area based on this characteristic. Model: GL5528 Max Voltage (DC): 150V Max Power Consumption: 100mW Photo resistance : 20k Ohm Dark resistance : 1M Ohm

    0,20 €
    Available
  • 1,00 € Available

    Main size: 25mm x 15mm x 20mm Motor shaft length: 8 mm, shaft diameter 2mm Rated voltage: 3V Speed: 3V when about 16,500 rpm per minute Single Weight: Approx 15g

    1,00 €
    Available
  • 1,00 € Available

    Pinout for ESP-WROOM-32 Wifi & Bluetooth Module. Compatible with ESP-07, ESP-08, ESP-12, ESP-12e. Package includes Breakout PCB Two 2x9 pin headers (not soldered) *The package does not contain the wifi module.

    1,00 €
    Available
  • 0,70 € Available
    New

    Jumper Cable wires usefull for connect electronic components on a breadboard without soldering. Both ends of the wires are male pins. It comes in multi colors pack Premium Jumper Wires Pack of 10 in different colors Female / Female Connector Length 30cm Suitable with 2.54mm Pitch

    0,70 €
    Available
  • 0,70 € Available
    New

    Jumper Cable wires usefull for connect electronic components on a breadboard without soldering. Both ends of the wires are male pins. It comes in multi colors pack Premium Jumper Wires Pack of 10 in different colors Male / Female Connector Length 30cm Suitable with 2.54mm Pitch

    0,70 €
    Available
  • 0,70 € Available
    New

    Jumper Cable wires usefull for connect electronic components on a breadboard without soldering. Both ends of the wires are male pins. It comes in multi colors pack Premium Jumper Wires Pack of 10 in different colors Male / Male Connector Length 30cm Suitable with 2.54mm Pitch

    0,70 €
    Available
  • 3,50 € Available

    ATMega328 32K microcontroller with pre-loaded Arduino UNO bootloader AVR microcontroller Flash memory organisation: 32kx8bit EEPROM memory capacity: 1024B SRAM memory capacity: 2048B Case: DIP28 Clock frequency: 20MHz Mounting: THT Operating voltage: 1.8...5.5V ** For Detailed information refer to the datasheet below

    3,50 €
    Available
  • 0,50 € Available

    Make your Arduino portable. Connect the power of your Arduino board to a 9V battery with this adapter. **Batteries not included.

    0,50 €
    Available
  • 1,20 € Available

    Suitable for Arduino and other devices (like printers) Type A Male Connector Type B Male Connector Color may differ (usually black) Length 1.4m-1.8m

    1,20 €
    Available
  • 1,90 € 2,50 € Available
    Sale!

    Features Voltage : 5VDC) Current: <2mA. Output signal: Electric frequency signal, high level 5V, low level 0V. Sensor angle: <15 degrees. Detection distance: 2cm-450cm. High precision: Up to 0.3cm Input trigger signal: 10us TTL impulse Echo signal : output TTL PWL signal  Mode of connection:  VCC trig(T) echo(R) GND 

    1,90 € 2,50 €
    Available
  • 3,00 € Available

    Jumper Cable wires usefull for connect electronic components on a breadboard without soldering. Both ends of the wires are male pins. It comes in multi colors pack - Color: Black + white + yellow + green- Cable length: Assorted - Between 12cm and 24cm- Can be used between any female headers or between two points on the breadboard- 65 pieces per pack

    3,00 €
    Available
  • 4,00 € 4,50 € Available
    Sale!

    This is a full-size breadboard with 830 tie points. It is solderless allowing to easily connect circuits of electronic components. 830 tie point breadboard Color: White ABS plastic material Completely reusable Coordinates for easy component placement Stackable Accepts a variety of wire sizes (20-29 AWG) Dimensions: 164mm x 54mm x 9mm Origin: China

    4,00 € 4,50 €
    Available
  • 1,20 € Available

    The Photo Resistor Module is used to indicate the presence or absence of light. The module can also be used to measure light intensity. This module allows for easy sensing of light levels from within your Arduino controller. Photosensitive Sensor Operating voltage 5V

    1,20 €
    Available
  • 2,00 € Available

    Specification: Signal Processing; BISS0001IC Voltage: 5V – 20V Power Consumption: 65mA TTL output: 3.3V, 0V Delay time: adjustable (0.3 sec – 10 minutes) Lock time: 0.2 sec Trigger methods: L – disable repeat trigger, H - enable repeat trigger Range: <120 degree, <7 meters Temperature: – 15 ~ +70 Dimension: 32x24 mm

    2,00 €
    Available
  • 3,00 € Available

    DC Voltage: 2.5 - 6V Working Current: 130 - 220mA Power: 0.4 - 1.5W Maximum Lift: 40 - 110cm Flow Rate: 80 - 120l/h Outside diameter of water outlet: approx. 7.5mm Inside diameter of water outlet: approx 4.7mm Size (Diameter x Lenght x Height): approx. 24mm x 45mm x 33mm Wire Length: apro. 15 - 20cm Material: Plastic Continuous Working Life: 500 hours

    3,00 €
    Available
  • 6,80 € Available

    Input voltage: 3.6-6V Working current: matching for 30 mA, matching the communication for 10 mA Output Power Class: Class 2 Size: 43mm x 15mm

    6,80 €
    Available
  • 9,50 € Available

    SONOFF Smart Home Switch WiFi WiFi protocol: 2.4Ghz b/g/n Frequency: 50Hz / 60Hz Max Load: 220V AC 10A / 2200W Power: 100V - 240V AC Wireless Security: WEP/WPA-PSK/WPA2-PSK Control: Mobile App Remote ON/OFF Counter / Time Certifications: CE/RoHS/FCC

    9,50 €
    Available
  • 17,50 € Available

    SONOFF 2 Channel Smart Home Switch WiFi WiFi protocol: 2.4Ghz b/g/n Frequency: 50Hz / 60Hz Max Load: 220V AC 16A / 3500W Power: 90V - 250V AC Protection: IP20 Material: FR-ABS V0 Wireless Security: WEP/WPA-PSK/WPA2-PSK Control: Mobile App Remote ON/OFF Counter / Time Certifications: CE/RoHS/FCC

    17,50 €
    Available
Showing 1 - 18 of 122 items