Ethernet Module ENC28J60 SPI interface mini version
Portable USB LED with white light Power: 5V USB
The case is made of ABS material. Size: 9.5cmx6.2cmx2.7cm Color: white
The case is made of ABS material. Size: 9.5cmx6.2cmx2.7cm Color: black
The case is made of ABS material. Size: 9.5cmx6.2cmx2.7cm Color:...
Charging Voltage: 8.4V Suitable for 2S 7.4V 8.4V Lipo Battery Overcharge...
The Official Raspberry Pi Power Supply! This PSU supports up to 3A of...
The speed and performance of the new Raspberry Pi 4 is a step up from...
MQ-9 gas sensor has high sensitivity to Carbon Monoxide, Methane and...
Model: TEC1-12706 Size: 40mm x 40mm x 4mm Operates from 0~15.2V DC and...
The speed and performance of the new Raspberry Pi 4 is a step up from earlier models. For the first time, we've built a complete desktop experience. Whether you're editing documents, browsing the web with a bunch of tabs open, juggling spreadsheets or drafting a presentation, you'll find the experience smooth and very recognizable
Broadcom BCM2837B0, Cortex-A53, 64-bit, quad-core SoC @ 1.4GHz 1GB LPDDR2 SDRAM 2.4GHz/5GHz IEEE 802.11 b/g/n/ac Wireless LAN (WLAN) Bluetooth Low Energy v4.2 (BLE) Gigabit Ethernet over USB 2.0 (maximum throughput 300Mbps) 4 x USB 2.0 Ports Power supply requirements - 5V/2.5A DC via micro USB or GPIO
Features:High quality 5v relay. LED status indicator High Current relay, AC250V 10A ; DC30V 10A Perfect for Arduino Projects and more Channels: 8 Product may differ from the picture
Features Voltage : 5VDC) Current: <2mA. Output signal: Electric frequency signal, high level 5V, low level 0V. Sensor angle: <15 degrees. Detection distance: 2cm-450cm. High precision: Up to 0.3cm Input trigger signal: 10us TTL impulse Echo signal : output TTL PWL signal Mode of connection: VCC trig(T) echo(R) GND
MCU: ATmega328 Operating Voltage (logic level): 5 V Input Voltage (recommended): 7-12 V Input Voltage (limits): 6-20 V Digital I/O: 14 (6 PWM) Analog Input: 8 DC Current per I/O: 40 mA Flash Memory: 32 KB of which 2 KB used by bootloader SRAM: 2 KB EEPROM: 1 KB Clock Speed: 16 MHz Dimensions: 0.73″ x 1.70″ Note: Pin headers included/soldered
DS1307 I2C real time clock chip (RTC) 24C32 32K I2C EEPROM memory Compact design, 27mm * 28mm * 8.4mm Fully charged, can provide DS1307 timing 1 year. Perfect for Arduino Projects and more Two-wire serial interface *No Battery Included
Ethernet Shield, based on the Wiznet W5100 Chip Supported by the official Ethernet Library Micro-SD card slot Compatible with Duemilanove (168 or 328), Uno & Mega (1280/2560) Network (IP) stack capable of both TCP and UDP Supports up to 4 simultaneous socket connections
Jumper Cable wires usefull for connect electronic components on a breadboard without soldering. Both ends of the wires are male pins. It comes in multi colors pack - Color: Black + white + yellow + green- Cable length: Assorted - Between 12cm and 24cm- Can be used between any female headers or between two points on the breadboard- 65 pieces per pack
WiFi Module – ESP-12E Uses CH340G replace the CP2102 USB: micro USB port for power, programming and debugging Headers: 2 x 15p 2.54mm pitch (with access to GPIOs, SPI, UART, ADC, and power pins) Buttons: Reset, Flash Power: 5V Size: 50 x 25 x 14 mm
Pitch: 2.54mm Thickness : 1.6mm Plated through holes Single sided Dimensions: 90 x 150mm
Drives 4 DC or 2 stepper or 2 Servo motors Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single/double coil or interleaved stepping 4 H-Bridges: 0.6A per bridge (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC 2 external terminal power interface, for...
Light intensity sensor module Data output range resembles luminance from 0-65535 lux I2C Interface No external parts required Provides simple digital output
WiFi Module – ESP-12E USB: micro USB port for power, programming and debugging Headers: 2 x 15p 2.54mm pitch (with access to GPIOs, SPI, UART, ADC, and power pins) Buttons: Reset, Flash Power: 5V Size: 50 x 25 x 14 mm