Ethernet Module ENC28J60 SPI interface mini version
Portable USB LED with white light Power: 5V USB
The case is made of ABS material. Size: 9.5cmx6.2cmx2.7cm Color: white
The case is made of ABS material. Size: 9.5cmx6.2cmx2.7cm Color: black
The case is made of ABS material. Size: 9.5cmx6.2cmx2.7cm Color:...
Charging Voltage: 8.4V Suitable for 2S 7.4V 8.4V Lipo Battery Overcharge...
The Official Raspberry Pi Power Supply! This PSU supports up to 3A of...
The speed and performance of the new Raspberry Pi 4 is a step up from...
MQ-9 gas sensor has high sensitivity to Carbon Monoxide, Methane and...
Model: TEC1-12706 Size: 40mm x 40mm x 4mm Operates from 0~15.2V DC and...
Features Voltage : 5VDC) Current: <2mA. Output signal: Electric frequency signal, high level 5V, low level 0V. Sensor angle: <15 degrees. Detection distance: 2cm-450cm. High precision: Up to 0.3cm Input trigger signal: 10us TTL impulse Echo signal : output TTL PWL signal Mode of connection: VCC trig(T) echo(R) GND
Light intensity sensor module Data output range resembles luminance from 0-65535 lux I2C Interface No external parts required Provides simple digital output
Specification: Signal Processing; BISS0001IC Voltage: 5V – 20V Power Consumption: 65mA TTL output: 3.3V, 0V Delay time: adjustable (0.3 sec – 10 minutes) Lock time: 0.2 sec Trigger methods: L – disable repeat trigger, H - enable repeat trigger Range: <120 degree, <7 meters Temperature: – 15 ~ +70 Dimension: 32x24 mm
U-blox NEO-6M GPS moduleCeramic-Antennabuild-in EEPROMThis module is compatible with APM2 and APM2.5, and EEPROM can save all your configuration data.Interface: RS232 TTLPower: 3-5vBaudrate default:9600bps
DS18B20 temperature sensor 9 to 12 bit adjustable resolution 1-Wire interface- requires only one digital pin for communication Power supply range:3.0V-5.5V ±0.5°C Accuracy from -10°C to +85°C Usable temperature range: -55 to 125°C (-67°F to +257°F) Stainless steel tube size:Approx.6*50mm(Diameter*Length) red (VCC), yellow(DATA) , black(GND) Cable length:...
Sensor adaptable to ambient light, having a pair of infrared emitting and receiving tubes. Transmitting tubes emit infrared certain frequency, when the direction of an obstacle is detected (reflection surface), the infrared reflected is received by the reception tube Adjustable detection distance knob Distance range of 2 ~ 30cm Voltage of 3.3V- 5V
The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is linearly proportional to the Celsius temperature. It also doesn’t require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C to +125°C temperature range.
Module Features: Detection: Fire / Flame Light Source Wavelength: 760nm to 1100nm Detection angle: 60 degrees Sensitivity: Adjustable by potentiometer Operating Voltage 3.3V-5V Output: Digital & Analog PCB size: 3.2cmx1.4cm fixed bolt holes for easy installation
Bracket ultrasonic sensor bracket fixture intelligent car supporting height adjustable Screws and nuts are included
Useful for prototyping/projects. Invensense MPU-6050 6-Axis (Gyro & Accelerometer) Very useful in prototyping systems Jumper Configurable 1x10 pin header Power supply configurable (5V or 3.3V) I2C Pull-up resistors Includes pin header & jumpers Manufacturer: Innoesys (www.innoesys.com) ** For Detailed information refer to the datasheet below
Photoresistor is a resistor which made of semi-conductor material,and the conductance changes with luminance variation . The photoresistor can be manufactured with different figures and illuminated area based on this characteristic. Model: GL5528 Max Voltage (DC): 150V Max Power Consumption: 100mW Photo resistance : 20k Ohm Dark resistance : 1M Ohm
The LM135, LM235, LM335 are precision temperature sensors which can be easily calibrated. They operate as a 2-terminal Zener and the breakdown voltage is directly proportional to the absolute temperature at 10mV/°K
Photoresistor is a resistor which made of semi-conductor material,and the conductance changes with luminance variation . The photoresistor can be manufactured with different figures and illuminated area based on this characteristic. Model: LDR07 - PGM5537 Max Voltage (DC): 150V Max Power Consumption: 100mW Photo resistance : 50k Ohm Dark resistance : 2M Ohm
This is a low cost humidity and temperature sensor with a single wire digital interface. The sensor is calibrated and doesn't require extra components so you can get right to measuring relative humidity and temperature. DHT11 output calibrated digital signal. *See below for more details