Κανένα προϊόν
Οι τιμές είναι μετά φόρων
Filament type: PET-G Colour: Super Blue Transparent Printing...
Filament type: PET-G Colour: Light Gray Printing temperature: 220-250°C...
Filament type: PET-G Colour: Graphite Printing temperature: 220-250°C...
Filament type: PET-G Colour: Galaxy Gray Printing temperature:...
Filament type: PLA Colour: Bright Green Printing temperature: 200-235°C...
Χρώμα: διαφανές Πυκνότητα στους 20° C: 0,79 g / cm3 Σημείο ανάφλεξης: 12...
Ιδανικό για χειροκίνητη επικασσιτέρωση για την αποκατάσταση της...
STM32G071RBT6 microcontroller in LQFP64 package 32.768 kHz crystal...
Κατασκευαστής: Nextool Μοντέλο: NE0126 Φωτεινότητα: έως 2000lm Χρόνος...
Τύπος: Mπαταρία λιθίου Κατηγορία: CR2032 Τάση μπαταρίας: 3V Συσκευασία:...
Παρασκευή που περιέχει υψηλής καθαρότητας ισοπροπυλική αλκοόλη που...
Εργονομικός σχεδιασμός για άνετη χρήση Οπτικός σένσορας ανάλυσης...
Σύνδεση: Ασύρματη 2.4GHz Εμβέλεια: έως 10m Ανάλυση: 800/1200/1600 dpi...
Speaker size: 14.2mm Sensitivity: 91dB ± 3dB Frequency range:...
Συνδεσιμότητα: Bluetooth v5.0, mini-jack 3,5mm, Ασύρματο, Ενσύρματο...
Total power output:RMS 24W Frequency response:70 HZ-20 KHZ +/-9db Signal...
Producer: Rebeltec Model: Long+ Width: 780 mm Length: 300 mm Thickness:...
Producer: Rebeltec Model: SliderM+ Width: 350 mm Length: 250 mm...
Producer: Rebeltec Model: SliderS+ Width: 250 mm Length: 200 mm...
Gaming USB Sound Card Chipset: CM108B 2.0 Cable length: 1.2m Wire...
TrueWireless Stereo Plus for easier pairing and better connectivity Up...
TrueWireless Stereo Plus for easier pairing and better connectivity Up...
Reinforced, braided cable braid Quick Charge: 1.5A (max) Features: fast...
iPhone 14 Pro Max Protect phone screen Resistant to scratches and...
iPhone 14 Pro Protect phone screen Resistant to scratches and absorbs...
iPhone 14 Plus Protect phone screen Resistant to scratches and absorbs...
iPhone 14 Protect phone screen Resistant to scratches and absorbs...
iPhone 13 / 13 Pro Protect phone screen Resistant to scratches and...
iPhone 13 Pro Max Protect phone screen Resistant to scratches and...
iPhone 13 Mini Protect phone screen Resistant to scratches and absorbs...
Compatibility: USB v2.0 standard Serial:RS-485 Serial: Screw terminal...
The onboard MAX485 chip is a low power consumption, limited swing rate...
Model: STM32F103C8T6 Core: ARM 32 Cortex-M3 CPU Debug mode: SWD 72MHz...
Suitable for 28BYJ-48 Step Motor Stepper motor driver board with ULN2003 A, B, C, D four-phase LED indicates the status of the stepper motor work. Stepper motor with a standard interface, when used directly pluggable. Drive Module Board Size:28mm x 28mm x 20mm *Step Motor is not included
A4988 is a complete microstepping motor driver with built-in translator for easy operation.Package included: 1 x Step motor driver module 1 x Heatsink
Double H bridge drive Chip: L298N (ST) Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A(MAX single bridge) Max power: 25W Size:43 x 43 x 26mm
Drives 4 DC or 2 stepper or 2 Servo motors Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single/double coil or interleaved stepping 4 H-Bridges: 0.6A per bridge (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC 2 external terminal power interface, for...
5V compatible, 3.3V microcontroller can be used 6 "address select" pins for configuring up to 62 ICs on a single I2C bus PWM frequency adjustable up to approximately 1.6kHz 12-bit frequency resolution (equates to about 4µs resolution at 60Hz refresh rate) Configurable as push-pull or open-drain output The output enable pin can disable all output quickly
The Arduino Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. Operating Voltage: 5V to 12V Motor controller: L298P, Drives 2 DC motors or 1 stepper motor Max current: 2A per channel or 4A max (with external power supply) Current sensing: 1.65V/A